Accessories

The IP65 Charger is already protected against dust, and water spray - now you can protect it from accidental damage too. This rubber bumper allows it to withstand the knocks and bangs of workshop life. It will extend the life of your charger, and it has an easy-carry handle, ...or hang it from a hook when not in use.There are two sizes available: Blue Smart IP65 Charger 12/10, 12/15 & 24/8Blue Smart IP65 Charger 12/25 & 24/13

This Wall Mount will be especially useful if you like to keep your smart charger handy - above your workshop bench, for example. Now the charger can be used without even moving it!

Smart and professional; this new snap shut carry case provides protective stowage and easy transport for your Blue Smart IP65 charger, and its accessories.Compartments accommodate the charger, its input/output cables; plus the battery-clamp/eyelet cable options.There are two sized available:For BPC Chargers up to 12/15 and 24/8 - 295 x 350 x 105mmFor BPC Chargers 12/25 and 24/13 - 345 x 520 x 130mm(Charger and accessories not included)

The UFR1001E monitors voltage and frequency in plants for own generation of electricity. It fulfills the requirements of VDE-AR-N 4105 bdew-directive, G59/3, G83/2 and ÖVE/ÖNORM E 8001-4-712:2009 for generators connected to the public grid. For more information, we refer you to the datasheet and certificates below which are available to download. Or visit www.ziehl.de and look for the UFR1001E under the Mains monitoring group.Note that we also stock a pre-built box including the Ziehl UFR1001E, two in-line 63A contactors and a main circuit breaker: the Anti-Islanding Box 63A single and three phase.

The Anti-Islanding Box 63A single and three phase is a combination of an anti-islanding device, the Ziehl UFR1001E, two in-line contactors and main circuit breaker. It is suitable for both single phase or 3 phase systems. It is rated up to 63A per phase and all parts are conveniently housed in an IP65 rated enclosure. The Anti-Islanding Box can be added to a grid-feeding inverter/charger system (ESS) to meet local anti-islanding regulations. Note that Ziehl UFR1001E is also available as a separate product, see its product page.

The VE.Direct to USB interface connects products with a VE.Direct connection to devices with a USB port, for example a computer. With this cable it is also possible to connect more than two VE.Direct products to a single CCGX.

Connect products with a VE.Direct connection and an RS232 connection with Victron's VE.Direct to RS232 interface.

The Victron RS232 to USB Converter connects Victron products with an RS232 port to a device that has a USB inlet, such as a computer or a GX device. It’s commonly used for configuring settings, monitoring, or integrating RS232-based devices into systems that only support USB.

The MK3-USB allows the following products to connect to a computer for configuration and firmware updates:Multi, MultiGrid, MultiPlus, MultiPlus-II, Quattro, VE.Bus BMS V2, Inverter/Charger settings in ECOmulti, EasySolar, EasyPlus, and Inverters with a VE.Bus communication port.

Easily mount a BMV-700 series or MPPT Control on a wall.

Wall mount enclosure for 65 x 120mm GX panels.

The VE.Can resistive tank sender adapter allows a standard resistive tank level sender to connect to the Color Control GX. It is compatible with both European standard 0-180 Ohm and United States standard 240-30 Ohm tank level senders and is accurate to ±1%. It is easily configurable to resistive senders from fuel, fresh water, waste water, well water, oil and black water (sewage) tanks. It supports up to 16 tanks of each type. The unit is a simple setup with two small rotary switches and it gets its power from the VE.Can network.When you use a Skylla-i or a MPPT with CAN bus in the system, the power to the CAN bus will be supplied by either one of them. When the CAN bus is not powered by a Skylla-I or a MPPT, you will need the new VE.Can Power Cable to supply the power.  

The VE.Can RJ45 terminator comes in a bag of two when ordered separately. The terminators are also included with some products, for example with the CANUSB.

The CANUSB interface is used to connect a VE.Can product to a computer.

Victron shunts are used to accurately measure current in high-power DC systems.These shunts are available in sizes ranging from 500A to 6000A, all with a 50 mV voltage drop, and they all have M10 terminals. Available Models:- 500A / 50 mV- 1000A / 50 mV- 2000A / 50 mV- 6000A / 50 mV

RS485 to USB interface, available in 1.8 m and 5 m.

When the CAN bus is not powered by a Skylla-I or an MPPT, you will need the new VE.Can Power Cable to supply the power.

This cable can be used to extend the BMS communication cables. This works for Lithium Smart batteries in combination with a Smart BMS or between Lithium NG batteries in combination with a NG BMS. It ships in a bag of 2 pieces and is available in 1, 2, 3 and 5 m lengths.

Use this cable to connect a Skylla-i to a VE.Bus BMS. The VE.Bus BMS will then disable the Skylla-i charger when the batteries are fully charged.

In the Orion-Tr Isolated DC-DC Chargers the remote on/off circuit is referenced to the primary battery (e.g. starter battery). The Orion-Tr DC-DC Charger Isolated remote cable is intended for applications where the remote on/off signal is referenced to the secondary battery (e.g. lithium battery with BMS).

Use this cable to connect a Victron product with a VE.Can port to a NMEA 2000 network. More information in the NMEA 2000 & MFD integration guide.