Всички продукти

Connect products with a VE.Direct connection and an RS232 connection with Victron's VE.Direct to RS232 interface.

The Victron RS232 to USB Converter connects Victron products with an RS232 port to a device that has a USB inlet, such as a computer or a GX device. It’s commonly used for configuring settings, monitoring, or integrating RS232-based devices into systems that only support USB.

The MK3-USB allows the following products to connect to a computer for configuration and firmware updates:Multi, MultiGrid, MultiPlus, MultiPlus-II, Quattro, VE.Bus BMS V2, Inverter/Charger settings in ECOmulti, EasySolar, EasyPlus, and Inverters with a VE.Bus communication port.

Easily mount a BMV-700 series or MPPT Control on a wall.

Wall mount enclosure for 65 x 120mm GX panels.

The VE.Can resistive tank sender adapter allows a standard resistive tank level sender to connect to the Color Control GX. It is compatible with both European standard 0-180 Ohm and United States standard 240-30 Ohm tank level senders and is accurate to ±1%. It is easily configurable to resistive senders from fuel, fresh water, waste water, well water, oil and black water (sewage) tanks. It supports up to 16 tanks of each type. The unit is a simple setup with two small rotary switches and it gets its power from the VE.Can network.When you use a Skylla-i or a MPPT with CAN bus in the system, the power to the CAN bus will be supplied by either one of them. When the CAN bus is not powered by a Skylla-I or a MPPT, you will need the new VE.Can Power Cable to supply the power.  

The VE.Can RJ45 terminator comes in a bag of two when ordered separately. The terminators are also included with some products, for example with the CANUSB.

The CANUSB interface is used to connect a VE.Can product to a computer.

Victron shunts are used to accurately measure current in high-power DC systems.These shunts are available in sizes ranging from 500A to 6000A, all with a 50 mV voltage drop, and they all have M10 terminals. Available Models:- 500A / 50 mV- 1000A / 50 mV- 2000A / 50 mV- 6000A / 50 mV

RS485 to USB interface, available in 1.8 m and 5 m.

A cable to connect the BMV shunt to the BMV head unit. A RJ12 cable ships standard with a BMV battery monitor, but if this cable is too long or too short it can be replaced by one of these cables, lengths available from 0.3 up to 30 meters.

A cable to connect Digital Multi Control, Inverter Control, Interface MK3-USB, VE.Bus connections between multiple VE.Bus devices and to make VE.Bus and VE.Can connections to a GX device.

This splitter is used to connect the MultiPlus 500VA - 1600VA range in parallel and 3 phase configurations, or in other installations where multiple VE.Bus ports are required.

Use this cable to connect a CAN-bus enabled battery, not from Victron, to a Victron system. There are two types, A and B. See the manual for details on which cable to use for which brand of batteries.

• Waterproof Shore Power Cable and Inlet IP56 • Moulded Plug and Connector • Power indication LED • Protection Cap • Stainless Steel Inlet Available in: 15M 16A 25M 16A 15M 25A 25M 25A

This cable connects the VE.Bus BMS to the Smart BMS 12/200, enabling the alternator charge control feature of the BMS 12/200 to be used in systems with a VE.Bus BMS. The BMS 12/200 will limit the alternator charge current to a safe value and stop the charging process in case of a battery alarm. This helps protect both the alternator and the lithium battery.​

Some of the USB plugs on our cables are too long to fit in the Wall mount box with a Color Control GX. Use this USB extension cable. Available in 0,3 m length.

The VE.Direct cable is available in different lengths. There is a straight and 90 degree angle model. Please check our pricelist for all available models.

Use this cable to connect the following products to the VE.Bus BMS: - Skylla-TG all models - Battery Protect models BP40i, BP60i and BP200i (all discontinued). The cable translates the remote on/off driver logic from the VE.Bus BMS (normally high, and open circuit in case of alarm) to the logic needed by above products: active pull down to switch off.

The Lynx Class-T Power In connects and fuses up to two strings of Lithium batteries. It features a positive and negative busbar, and connections for two Class-T fuses as well as a connection to ground the DC system. The Class T-fuses, available in 225A, 250A, 350A and 400A, must be purchased separately. For installations using three or more strings of Lithium batteries, use multiple Lynx Class-T modules. As a core component of the Lynx Distribution system, the Lynx Class-T seamlessly integrates with all other M10 Lynx products.

A modular DC busbar with spaces for four DC fuses. It monitors the status of each fuse and displays its condition with an LED on the front. The Lynx Distributor is part of the modular Lynx distribution system, available as M8 and M10 models.