Всички продукти

The Battery Alarm is a small and low cost alarm panel which monitors your battery bank. It features both audible and visual alarms, as well as a potential free contact with normally open and normally closed contacts. Alarm thresholds and hysteresis are programmable by DIP switches. See manual for more information.

The Charger Control panel provides remote control and monitoring of the charge process with LED indication of the charger status. In addition, the remote panel also offers output current adjustment that can be used to limit the output current and thus the power drawn from the AC supply. This is particularly useful when operating the charger from limited shore power or small gensets. The panel can also be used to change the battery charging parameters. The brightness of the LEDs is automatically reduced during night time. Connection to the charger is with a standard UTP cable.

This panel is for all VE.Direct inverters.

The 2 meter extension cable is an accessory of the Blue Smart IP65 Charger with DC connector.

This panel is intended for Inverters equipped with a UTP remote monitoring and control socket. It can also be used on a MultiPlus Inverter/Charger when an automatic transfer switch but no charger function is desired. The brightness of the LEDs is automatically reduced during night time. Only for models: 12/1200, 12/1600, 12/2000, 12/3000, 12/5000, 24/1200, 24/1600, 24/2000, 24/3000, 24/5000, 48/3000 and 48/5000.

VE.Net GMDSS panel

A remote on-off switch for the Skylla-TG Charger.

Remote Panel for BlueSolar PWM-Pro.

Smart Battery Sense is a wireless battery voltage and temperature sensor for Victron MPPT Solar Chargers.With voltage and temperature sense in place, batteries will be better charged; improving charging-efficiency and prolonging battery life.

Energy Meters are typically used in an Energy Storage System, to measure the power and energy of the entire application at the distribution box and minimises energy import or export to the grid. They can also be used to measure the output of a PV inverter or AC loads and display the data on GX devices such as the Cerbo GX or Ekrano GX and the VRM Portal.There are several models available from Victron:Victron VM-3P75CT energy meter (Ethernet and VE.Can - for three-phase and split-phase, uses supplied CTs, max. 80A per phase)ET112 (RS485 - for single-phase max. 100A)ET340 (RS485 - for three-phase max. 65A)EM24 Ethernet (Ethernet - for three-phase max. 65A)EM540 (RS485 - for three-phase max. 65A)For more information, please see the Selection Guide - Energy Meters PDF below.

The AC Current sensor is a simple external current sensor used to measure AC Current, Power (VA) and calculate energy of a PV Inverter connected to the AC input or output of a Multi or Quattro. These values can then be displayed and sent to the VRM-website by the Color Control. The two measurement wires can be connected to the AUX and/or temperature sense input of a Multi or Quattro.

Current Transformer 100A:50mA for MultiPlus-II / MultiGrid-II to implement PowerControl and PowerAssist and to optimize self-consumption with external current sensing. See MultiPlus-II datasheet for more details.Note that there are two types:CTR11xxxx has a jack connector CTR12xxxx has a wire end Both types are available with 1, 5 and 20 meter cable lengths.Current Transformer 400A:50mA for MultiPlus-II (10m) Wire-end, has a wire end and 10 meter cable length.

Temperature Sensor for BlueSolar PWM-Pro

Spare battery temperature sensor for the Inverter RS Smart Solar.

Temperature sensor for Quattro, MultiPlus and GX Device.

The CAN-bus Temp. Sensor is a battery temperature sensor for the Buck-Boost DC/DC converter range and is an essential accessory when the Buck-Boost DC/DC converter is connected to a LFP lithium battery. Temperature sensing is needed when LFP lithium batteries are charged at low temperatures. The charge current to a lithium battery has to be reduced once the battery temperature drops below 5 degrees and the charge current has to stop when the temperature drops below zero. The CAN-bus Temp. Sensor takes care of this. It measures the lithium battery temperature and sends this to the Buck-Boost DC/DC converter. The Buck-Boost DC/DC converter will reduce or stop charge when the battery temperature drops too low. In addition to this, the CAN-bus Temp. Sensor can also be connected to the temperature sensor terminal in a Multi or Quattro, so the Multi or Quattro can reduce or stop charging when the battery temperature drops too low.

The Ekrano GX Wall Mount accessory enables quick and secure installation on a solid wall. Only four screws are needed, with no additional drilling or cut-outs required. The enclosure is easily accessible: it opens from the top with two screws and folds forward without being removed from the wall, allowing straightforward connection of additional cables to the interfaces of the Ekrano GX from the sides, top, bottom, or back.

The Pre-charge Cable allows internal capacitors of an inverter, inverter/charger or MPPT to be pre-charged via the DC terminals before connecting the battery. This method ensures that connecting the battery will not result in arcing at the connection point.

The SolidSwitch 104 will switch DC loads of up to 70V/4A and can be controlled by a low power digital signal. The DC load can be resistive, capacitive or inductive (such as the coil of a high-power contactor).The SolidSwitch is not reverse polarity protected and not short circuit proof.

The GX Touch 50 & 70 protection cover prevents damage from UV light during prolonged exposure to the sun.

The GX Touch wall mount accessory allows easy mounting of the GX Touch on a solid wall. No drilling or cut-out is required, other than the three screws that fix the wall mount onto the wall.